Level 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Caps & crowns
Before
After
Before
After
Before
AfterOlympia Chimney Chimney Repair in Manhattan: What to Know First
Olympia Chimney chimney repair in Manhattan typically runs $275-$1,800 depending on whether we’re repointing mortar joints, rebuilding a spalled brick section, or replacing flashing around the base. Most repairs are completed in a single day, and you’ll have a written price before we touch anything. If you own an Olympia Chimney system and you’re seeing water stains, crumbling mortar, or rust streaks, this page tells you exactly what’s happening and what it costs to fix. Call (862) 319-8047 for a free estimate with a camera-scan inspection included.
This page is for Manhattan homeowners with Olympia Chimney products: stainless steel liners, chimney caps, and chase covers that were in thousands of New York City installations over the last two decades. We’re an independent Olympia Chimney service provider, which means we repair the full range of their products without any manufacturer restrictions on how we diagnose or what parts we use. Corrine Halstead and the Level Two Chimney Manhattan crew have pulled camera footage from Olympia flues all over this borough, from prewar co-ops on Riverside Drive to newer condos in Hudson Yards.
How Olympia Chimney Products Fail - and How We Fix Them
- Olympia stainless steel liners with pitting at the corbel line. Manhattan’s freeze-thaw cycle works on masonry, and when the chimney crown or flashing fails, water runs down the liner’s exterior. Over time that water sits at the smoke shelf and eats at the liner’s lower section. We spot this on camera as pitting or hairline rust at the first 18 inches above the smoke chamber. The fix is a partial liner section replacement or full reline if the pitting runs higher than the camera shows.
- Olympia chimney caps with corroded mounting screens. The screen mesh on Olympia caps was improved over the years, but earlier units used a galvanized screen that rusted in under ten years in Manhattan’s humid summers and salt air near the Hudson. We replace the cap with a stainless Olympia equivalent or a Copperfield cap if you want heavier gauge. The camera shows whether the cap’s the problem or just the first thing you noticed.
- Olympia chase covers with failed welds at the corners. Chase covers take the brunt of Manhattan weather, and welded corners eventually crack. Water seeps into the chase, rusts the top of the chimney or the fireplace framing below. We measure for a replacement chase cover, order it in stainless, and re-flash the chimney cap base. This is one of those repairs where the written quote matters more than usual, because the cost swings based on wall thickness and whether the chase itself has rotted.
- Spalling brick around the Olympia thimble where it exits the wall. In narrow Manhattan buildings, chimneys often punch through brick party walls. Water intrusion around the thimble damages brick and mortar, and what shows inside the home is just the visible part. We repair the spalled brick, repoint with a mortar matched to the building’s original mix, and re-seal the penetration with a flexible flashing that moves with the building.
- Mortar crown cracking above Olympia liner terminations. The heat cycling of an Olympia liner can accelerate crown cracking if the crown was never poured with an expansion joint. Water gets in and follows the liner down. We repair the crown with a properly mixed mortar, install or reset the liner’s rain cap, and pass the camera back down to confirm the interior is dry before we call the job done.
Our Olympia Chimney Chimney Repair Process
- 1
You call or text. We answer live, every time. We gather the basics: building type, symptom you’re seeing, and whether you’ve had any prior work done on the chimney.
- 2
We schedule a camera-scan inspection. NFPA 211 Level 2, camera down the flue, every time. You watch the footage live if you want to. We record it.
- 3
You get a written price before we start. No technician standing in your living room waiting for a yes. The camera report, written scope, written price, and written warranty get delivered together. Clause 1 of the Haven Standard requires it.
- 4
We decide parts with you. When OEM Olympia parts make sense, we use them. When an aftermarket part does the same job better or cheaper, we show you why. You approve the part before we order it, not after.
- 5
We repair and document. The repair is made, the area’s cleaned, and the camera goes back down or up to confirm the fix. You get a photo record of the entire job, not a before-and-after that hides the middle.
- 6
365-Day Done Right Promise kicks in. If it’s not done right, we make it right. Stamped on every Olympia chimney repair we perform.
BeforeAfterWhat Olympia Chimney Chimney Repair Costs in Manhattan
Here’s what we see on jobs across Manhattan, with real dollars:
- Mortar repointing around the Olympus cap or crown: $275-$600
- Flashing repair or replacement at the roofline: $450-$900
- Spalling brick repair (sectional or full face): $600-$1,800
- Chimney waterproofing after repairs: $350-$800
- Partial rebuild above the roofline: $1,200-$3,500
- Full Olympia liner replacement: $2,500-$6,000 depending on flue height and access
What moves the price: how much of the chimney is exposed, whether the building is a landmarked district requiring specific mortar matching, and how long the flue runs from fireplace to termination. Manhattan’s building stock varies wildly. A brownstone in Harlem with a three-story brick chimney is a different job than a condo terrace chimney on the Upper East Side. We give a written estimate before any work starts, and a free second opinion on any competitor’s written quote. Call (862) 319-8047 for exact numbers on your building.
Why Manhattan Homeowners Call Level Two Chimney Manhattan for Olympia Chimney Work
Because we show you the camera footage before we ask you to spend a dollar. That’s been our practice since our founding in 2009, and it’s Clause 4 of the Haven Standard: a documented photo record on every job, no exceptions. You don’t take our word for it. You watch the flue liner flex and read the creosote class on the report yourself. Corrine Halstead has spent the better part of two decades running chimney work across Manhattan, including older co-op buildings along Riverside Drive where the flues hadn’t seen a brush since the Carter administration. The camera doesn’t guess. Neither do we.
We’re multi-brand specialists. Alongside Olympia Chimney products, we regularly work with DuraFlex liners, HeatShield resurfacing, and Gelco waterproofing. That matters because it means we’re not married to one manufacturer’s solution. If your Olympia liner can be saved with HeatShield instead of replaced, we’ll show you that option on the report. Level Two Chimney Manhattan is independently owned and operated under the Haven Standard. Background-checked, uniformed technicians. License number displayed on every page. A named tech assigned to your job, and a text when they’re on the way.
FAQs
Most Olympia Chimney products carry a limited manufacturer warranty, typically 10 years on stainless components, but labor is rarely covered and the warranty requires the chimney be maintained annually and inspected at installation. We can pull your product’s date and serial from the unit during the inspection and help you understand what’s actually covered before you file a claim. Even if the parts are covered, you’ll want a written repair quote for the labor so you know your real out-of-pocket. Call (862) 319-8047 and we’ll walk through it.
It depends on where the damage is and how extensive it looks on camera. Pitting near the smoke shelf can sometimes be addressed with a partial liner section replacement. Corrosion higher in the flue, or any liner with holes or gaps at the joints, usually means full replacement. We don’t recommend replacement based on a guess. We show you the footage, mark the damaged sections, and give you a written price for repair and replacement side by side. You decide with the evidence in front of you.
Most Olympia caps, chase covers, and common liner components are available within 3-5 business days through our suppliers. We stock the most common sizes and profiles in our Manhattan warehouse for typical repair scenarios. Custom chase covers and specialty liner sections add a few days. We’ll tell you the parts timeline on the written quote so there’s no waiting without knowing.
Yes. A flashlight from the roofline tells you about the first 12 inches of the flue. A camera down the full liner shows you the actual condition, including cracks and water damage that aren’t visible from outside. This is the difference between repointing mortar on a crown that’s failing and catching a liner that’s about to fail before it does. Clause 4 of our standard requires the photo record on every job. We’ve worked this way since 2009, years before it became an insurance expectation. Your repair is only as good as the diagnosis. The camera is the diagnosis.
Water keeps moving. Through cracked mortar, around failed flashing, into the brick. Manhattan’s freeze-thaw cycles expand that water into cracks every winter, and the damage compounds year over year. What starts as a $400 repointing job becomes a $3,500 partial rebuild. And if the liner is compromised, the risk moves from water damage to fire and carbon monoxide. We don’t scare-sell on this. But we’ll show you exactly what the camera sees and what it means in plain terms. You can make the call with real information, not a sales pitch. For a free estimate with the camera included, call (862) 319-8047.
Written by Corrine Halstead, Owner, Level Two Chimney Manhattan at Level Two Chimney Manhattan, serving Manhattan and nearby areas.