Olympia Chimney Chimney Cap & Crown Nationwide

Olympia Chimney Chimney Cap & Crown in Manhattan: What to Know First

Olympia Chimney cap and crown work in Manhattan typically runs $425-$2,400 depending on whether we’re replacing a standard single-flue cap, fabricating a custom multi-flue cap, or rebuilding a spalled crown. Most Olympia Chimney cap replacements are done in one visit; crown rebuilds usually take two because the mortar needs cure time before we coat it. We’re an independent Olympia Chimney service provider, which means we work on their products daily but we’re not tied to their parts catalog or their pricing structure. If you own a home or co-op unit with an Olympia Chimney flue system and you’ve noticed rust streaks, spalling, or water in the firebox, call (862) 319-8047 and we’ll put a camera on it. Written price before anything gets touched.

Call (862) 319-8047

How Olympia Chimney Products Fail - and How We Fix Them

• Olympia Chimney stainless caps with rust at the screen seam. We see this on the standard Olympia single-flue caps installed across Manhattan rowhouses and older co-ops. The mesh screen is spot-welded at the corners, and ten years of wet Manhattan winters with freeze-thaw cycling pops those welds. Once the seam opens, the screen sags and a rust line forms. The fix is a full cap replacement, and we move up a gauge when we order the replacement so the next one actually survives the rooftop exposure. We’ve never had a callback on a gauge-up replacement.
• Crown spalling on Olympia masonry systems above Riverside Drive and Morningside Heights. The original crowns on a lot of Olympia Chimney masonry flues in pre-war buildings are plain mortar, sometimes poured over brick corbels, with no expansion joint. Mortar absorbs water, freezes at altitude, and spalls off in chunks. We rebuild with a proper two-inch concrete crown with a drip edge and a flexible bond break against the flue tile, then coat it with a breathable elastomeric crown coat that handles Manhattan’s temperature swings without cracking.
• Olympia multi-flue cap wind noise and drafting restriction. Some Olympia multi-flue caps use a flat-top design with a short skirt, and in buildings that catch crosswind off the Hudson or East River, owners get a low whistle or pulsing draft. It’s not a safety issue, but it’s maddening at night. We swap in a taller-skirt cap or a custom unit with better airflow geometry. The difference in draft is measurable with the camera and pressure readings, and the noise is gone immediately.
• OEM Olympia replacement parts that owners ordered online and couldn’t get to seat. This happens at least once a month. An owner buys an Olympia cap from a supply house, gets on a ladder, and discovers the base ring doesn’t match the flue tile dimensions of their older Olympia system. Olympia’s online catalog assumes standard dimensions; Manhattan pre-war flues are rarely standard. We measure the actual flue inside and out, then either adapt the part if it’s salvageable or order a correctly-sized aftermarket equivalent that fits the first time.
• Cap rust-through on Olympia galvanized units converted from oil to gas. This one is specific to buildings that converted heating fuel during the 2010s oil-to-gas push. The original galvanized Olympia cap was sized for oil exhaust, which is hotter and has less condensate. Gas exhaust is cooler and wetter. The cap rusts from the inside out, and by the time the rust shows through, the underside is compromised. We replace with the right stainless cap rated for gas condensing, and we document the before and after so the co-op board has a record.

Our Olympia Chimney Chimney Cap & Crown Process

1. 1
   You call, a live person answers. No voicemail, no web form. We ask about the symptom, the building type, and whether you know the Olympia model. If you have papers or photos, we’ll look at them. Then we book a window that works for you, and you get a text when the tech is on the way.
2. 2
   We put a camera on the flue and the cap. This is NFPA 211 Level 2, every time, regardless of whether you’re calling about a cap or a crown or just want a second opinion. The camera shows us exactly what the last sweep left behind and what’s actually failing. Corrine Halstead reviews every Olympia Chimney job’s footage personally before we quote.
3. 3
   We give you the written scope and price before work starts. Haven Standard Clause 1, always. You see the photos, you see the price, and you decide. If the cap can be adapted instead of replaced, we say so and price the adaptation. If the crown only needs coating instead of rebuilding, you’ll see the difference on the photo report.
4. 4
   Parts decision: OEM Olympia vs. quality aftermarket. If your system is under warranty and Olympia will cover the part, we order OEM. If it’s out of warranty, we source from our network (DuraFlex, HeatShield, Gelco, and other brands we trust) and pick the part that actually fits your flue dimensions. We tell you which one we’re using and why.
5. 5
   The repair, done by a background-checked, uniformed tech. Cap swaps are usually one visit. Crown rebuilds get the new crown poured, then a return visit to coat once the mortar is cured. We protect the roof, we clean up, and we don’t leave a mess for the super to complain about.
6. 6
   You get the photo record and the written warranty. Each visit includes a documented photo record of the before, during, and after. The 365-Day Done Right Promise applies: if the cap leaks or the crown coat fails in the first year, we come back and make it right. No arguments, no re-quote.

Before

After

What Olympia Chimney Chimney Cap & Crown Costs in Manhattan

Here’s what we actually charge for the most common Olympia Chimney scenarios, in writing, before anyone touches a ladder.

• Single-flue stainless steel cap replacement: $425-$675 installed, depending on flue tile dimensions and roof access.
• Custom multi-flue cap, fabricated to fit an irregular Manhattan flue array: $900-$1,600 installed, including the site measurement and fabrication.
• Crown coat only (crown is sound, just needs sealing): $550-$850, including surface prep and two coats of elastomeric crown coat.
• Full crown rebuild with drip edge and bond break: $1,400-$2,400, depending on crown footprint and whether we need to repair the flue tile top first.
• Cap plus crown rebuild together: $1,800-$2,800, which is the most common recommendation when the cap has rusted and the crown has spalled at the same time.

What moves the price: roof access difficulty, the number of flues under a single cap, whether we need a lift or can work from ladders, and whether the existing crown has to be fully demolished or just re-topped. You’ll always see the final number in writing before work starts. Call (862) 319-8047 for a free estimate, and if you have a written quote from another company, we’ll give you a free second opinion on it.

Why Manhattan Homeowners Call Level Two Chimney Manhattan for Olympia Chimney Work

We’ve been running camera-documented chimney inspections since 2009, years before most companies in Manhattan even offered a camera scan. That archive practice became Clause 4 of the Haven Standard, and it applies every single time we touch an Olympia Chimney system. Our techs are background-checked and uniformed, with license information displayed on the page, and the same named tech runs your job from start to finish. When an Olympia part doesn’t fit and we need a backup, we source through our network from DuraFlex, HeatShield, Gelco, and other brands we trust, so you’re never stuck waiting on a backorder or a warranty claim. The camera doesn’t guess. Neither do we.

FAQs